Page 28 If you have a client PC that cannot run Internet applications properly from behind the DI, then you can set the client up for unrestricted Internet access. It allows a computer to be exposed to the Internet. This feature is useful for gaming purposes. They are admin and user. User can only view the settings but cannot make any changes. NTP synchronizes com- puter clock times in a network of computers. This field is optional. The saved file or any other saved setting file can be loaded back on the Broadband Router.
To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used. Page 33 Click on Browse to browse the local hard drive and locate the firmware to be used for the update.
You can download firmware up- grades to your hard drive from the D-Link support site. Page 34 IP Security. Once VPN pass-through is enabled, there is no need to open up virtual services. If the device is rebooted, the logs are automatically cleared. You may save the log files under Log Settings. View Log- First Page - The first page of the log. Email Address - The email address to which the logs will be sent. The traffic counter will reset if the device is rebooted.
Page 40 Networking Basics Please follow all the instructions in this window: Click Next In the following window, select the best description of your computer. Click Next Click Next Enter a Workgroup name.
All computers on your network should have the same Workgroup name. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.
Page 43 Networking Basics In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Insert a disk into the Floppy Disk Drive, in this case drive A. The new settings will take effect when you restart the computer.
Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. Page Getting Started Naming your Computer In this window, enter the Computer name Select Workgroup and enter the name of the Workgroup All computers on your network must have the same Workgroup name.
To check on the IP Address of the adapter, please do the following: Right-click on the The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of A window similar to this one will appear. Type ping xxx. The computer used to configure the DI cannot access the Configuration menu. Each device must have a unique IP Address; Page 56 Troubleshooting 3.
Check that the drivers for the network adapters are installed properly. You may be using different network adapters than those illustrated here, but this procedure will remain the same, regardless of the type of network adapters you are using. Click OK. Page 58 RF noise, like microwaves, Monitors, electric motors, etc. If you have enabled Encryption on the DI, you must also enable encryption on all wireless clients in order to establish a wireless connection.
Page 59 6. Turn the DI back on again, and then turn on the client. Make sure that all devices are set to Infrastructure mode. Check that the LED indicators are indicating normal activity. If not, check that the AC power and Ethernet cables are firmly connected. Page 60 8. Resetting the DI to Factory Default Settings After you have tried other methods for troubleshooting your network, you may choose to Reset the DI to the factory default settings.
Remember that D-Link AirPlus G products network together, out of the box, at the factory default settings. The device has the utility built-in to a ROM chip in the device itself. The wiring in crossover and straight-through cables are different. The two types of cable have different purposes for different LAN configurations.
Check the help files included with your firewall software for more information on disabling or configuring it. Your computer must have an IP Address in the same range of the device you are attempting to configure. Most D-Link devices use the X range. Step 1 Click on Start and select Run. Page 71 Step 5 Access the web management.
This should open the login page for the web management. Follow instructions to login and complete the configuration. Note: Please configure the router with the computer that was last connected directly to the cable modem. Step 1 Log into the web based configuration by typing in the IP Address of the router default Turn the router off Leave them off for 2 minutes.
Page 74 from your computer or you will not be able to connect to the Internet. Step 1 Upgrade Firmware if needed. Please visit the D-Link tech support website at: firmware upgrade information. Step 2 Take a paperclip and perform a hard reset. With the unit on, use a paperclip and hold down the reset button on the back of the unit for 10 seconds. Turn back on. Wait about 30 seconds and log back into the router.
Continue to save the changes. A window similar to this one will appear. Page 34 IP Security. You may save the log files under Log Settings. Most D-Link devices use the To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used.
Page 76 To allow traffic from the internet to enter your local network, you will need to open up ports or the router will block the request. Step 2 Click on the Advanced tab and then click Virtual Server on the left side. This means that if you have an existing A URL is a specially formatted text string that defines a location on the Internet. Next, you will need to run the Network Setup Disk on all the other computers on your network.
Once VPN pass-through is enabled, there is no need to open up virtual services. Make sure that all devices are set to Infrastructure mode. Enter a name ichat1. You will need to open 3 ports in the Virtual Server section of your D-Link router. Step 9 Turn off your DSL modem for minutes. You can download portugies up- grades to your hard drive from the D-Link support site. With proper configuration, multiple users can access the Internet using a single account via the NAT device.
The two types of cable have different purposes for different LAN configurations. Please wait while the Network Setup Wizard configures the computer. Using a power supply with a different voltage rating than the one included with the DI will cause damage and void the warranty for this product. To play a game, you do not have to configure your router.
This LED blinks during data dk. D-Link, a leading maker of routers, is one company that sells products designed for setting up. This website uses cookies to improve your experience while you navigate through the website.
Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent.
You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website.
0コメント